Pins

A roofing contractor in Kenova, West Virginia inspected a home's roof after the owner found loose shingles in the yard. The contractor assessed the damage and prepared a detailed insurance estimate for repairs.

SCC Commercial and Metal Roofing repaired multiple leak points on an EPDM roof in Vanceburg, Kentucky. The team inspected, measured, and marked the damaged areas. After approval, they cleaned the surfaces and sealed all holes using silicone and acrylic products for long-lasting protection.

SCC Commercial and Metal Roofing completed a steep-slope roofing upgrade in Lexington, Kentucky. Crews added 2x4s across the roof deck and installed a single bubble barrier. They applied Flexion XL PVC membrane in low-slope areas and sealed it with thermal welding. Everlast metal panels, ridge caps, siding flashings, and brick counter flashing were also installed.

SCC Commercial and Metal Roofing completed a roof coating project in Warsaw, Kentucky. The team pressure washed two roof sections, applied a Tack Coat primer, reinforced seams with Spunflex in a basecoat, and finished with a white RAPID ROOF III top coat for added protection.

SCC Commercial and Metal Roofing installed a Flexion XL single-ply membrane roofing system in Falmouth, Kentucky. The team removed metal panels and sheathing, added insulation, fastened membrane rolls, welded seams with hot air, and finished parapet walls with new red cap trim and proper flashing on the bell tower.

SCC Commercial and Metal Roofing replaced an old standing seam roof in Vanceburg, Kentucky. Crews installed 1932 plywood sheathing, a single bubble vapor barrier, and new 26-gauge Everloc snap lock standing seam panels. They completed the project with rake trim, wall flashing, cut-in counter flashing, and cap trim on the shared parapet wall.

SCC Commercial and Metal Roofing completed roof maintenance in Ashland, Kentucky. Crews cleaned seams and protrusions, applied tack coat primer, embedded Spunflex fabric in a rapid roof basecoat, sealed gable ends with Kwik Kaulk, and inspected for necessary repairs. The work addressed potential leak points and reinforced roof durability.

SCC Commercial and Metal Roofing removed and replaced the metal roofing on a front gable and porch in Maysville, KY. The team installed drip edge trim, single bubble insulation, 28-gauge Everlast metal panels, proper sidewall flashing, transition seams with emseal, ridge caps with uni-vent, and sealed corners to ensure a weather-tight finish.

SCC Commercial and Metal Roofing repaired a metal roof in Inez, Kentucky. Technicians replaced rusted sections, installed flute-fill and 2.2-inch insulation, and applied a 60 mil PVC membrane. They heat-welded all seams and used t-patches at seam intersections to reinforce the roof structure and maintain a level surface across the deck.

SCC Commercial and Metal Roofing removed damaged metal panels and sheathing from an upper roof in Portsmouth, Ohio. The team installed new pine plywood, rigid insulation board, and a Flexion XL 60 mil single-ply membrane. They added welded drip edges, thermally fused seams, and extended the membrane up parapet walls before completing the project with new cap trim.

SCC Commercial and Metal Roofing restored a metal roof in Flemingsburg, Kentucky. The team removed rust, pressure washed the surface, ground old caulking, primed the roof, sealed fasteners, reinforced seams with fabric, and applied a white top coat to complete the project.

SCC Commercial and Metal Roofing installed synthetic felt and house wrap, then fitted Everlast metal roofing with emseal trim in Vanceburg, Kentucky. The team added a vented ridge system, soffits, fascia, drip edges, and mini rakes. They also installed Patina Green metal siding, wrapped posts, completed porch ceilings, and secured windows with house wrap tape and a rat guard.

SCC Commercial and Metal Roofing repaired a 15'x17' section of single-ply roofing in Hillsboro, Ohio. They removed bubbles, dried the insulation board, and cleaned the surface with brushes and cleaners. The team then applied Enduris liquid flashing to HVAC curbs and seams before coating the area with Enduris roof coating.

SCC Commercial and Metal Roofing inspected roof leaks during and after rainfall in Lexington, Kentucky. The team repaired problem areas with silicone and urethane, cleared all gutters, and fixed a raised outside rake. Measurements were taken on-site to ensure repair accuracy.

SCC Commercial and Metal Roofing completed metal roof restoration in Vanceburg, Kentucky. The team removed rust, cleaned with a 4200 psi pressure washer, primed the surface, replaced two pipe boots, caulked seams and fasteners, reinforced joints with Spunflex fabric, and applied a white PUMA XL Top Coat at two gallons per square.

SCC Commercial and Metal Roofing completed a roof repair in Vanceburg, Kentucky. The team cleaned and primed two pipes, one corner, a 16-foot EPDM seam, and a hole. They applied fabric and basecoat to the hole and sealed the other areas using Kwik Kaulk to address existing roof leaks.

SCC Commercial and Metal Roofing installed new pine plywood sheathing and approved insulation on a commercial roof in Vanceburg, Kentucky. The crew applied a Flexion XL 60 mil single-ply membrane, fused overlapping seams, extended membrane over parapet walls, and finished with new cap trim. Old materials and metal sheathing were removed and properly discarded.

SCC Commercial and Metal Roofing upgraded a roof in Vanceburg, Kentucky. The team installed 1x4 boards two feet on center, applied synthetic felt, and added vented ridge ventilation with Uni-Vent. They installed #1 28-gauge Everlast Metal panels, drip edge, sidewall flashing under siding, and pipe boots for weather protection.

SCC Commercial and Metal Roofing cleaned and primed all seams and protrusions on an EPDM roof in Vanceburg, Kentucky. They applied basecoat-reinforced Spunflex to the seams and sealed pipe boots and wall edges with bronze caulk. Skylight replacement remains pending.

SCC Commercial and Metal Roofing installed vented Everlast soffit and j-channel along all eaves and gable ends. The team also applied fascia metal to these roof edges in Sandy Hook, Kentucky. This service improves roof ventilation and edge protection, helping to maintain long-term roof performance.

SCC Commercial and Metal Roofing applied 360 S urethane sealer to the termination bar where the building connects to the cooler room. The crew sealed HVAC flanges with Kwik Kaulk and finished by sealing the front J channel. This service was completed in Maysville, Kentucky.

SCC Commercial and Metal Roofing installed a new metal roof overlay on a home that previously had 25-year-old shingles. The project took place in Vanceburg, Kentucky. Metal roofing was selected to replace aging shingles and extend the roof’s lifespan without removing existing materials.

SCC Commercial and Metal Roofing completed a full metal roof installation in Vanceburg, Kentucky. The team removed old materials, installed synthetic underlayment, drip edge, 28-gauge Everlast metal panels, flashing for valleys and walls, uni-vented ridge cap, and eave-mounted rain and snow guards. All components were securely fitted for durability and weather resistance.

SCC Commercial and Metal Roofing completed a free roof inspection in Ashland, Kentucky. The inspection found wind damage, including missing flashing and EPDM material pulled from the termination bar beneath a metal roof section. The report helps identify structural issues caused by severe weather.

SCC Commercial and Metal Roofing replaced a damaged lean-to roof in Covington, Kentucky. The crew removed old metal and rotten sheeting, installed new 2x4 roof decking, applied a vapor barrier, and added drip edges. They sealed seams with mastic, installed 28-gauge Everlast metal panels, a metal pipe boot, and finished all roof corners.

SCC Commercial and Metal Roofing completed a free roof inspection in Vanceburg, Kentucky. The inspection found wind damage, including lifted shingles along the valley, a missing full shingle, and detached shingle tabs. This report was prepared for insurance documentation.

SCC Commercial and Metal Roofing installed 1x4 supports two feet apart across the roof in Vanceburg, Kentucky. The crew added synthetic felt, 28-gauge Everlast metal panels, and a vented ridge system. They finished the job with a ridge cap, rakes, valleys with Emseal, and metal pipe boots for proper sealing and ventilation.

SCC Commercial and Metal Roofing completed a full metal roof installation in Manchester, Ohio. The crew removed debris and damaged sheathing, replaced all roof protrusions with new sheathing, installed 1x4s, drip edge, single bubble insulation, 28-gauge Everlast metal panels, mastic on seams, endwall and rake flashing, and a split pipe boot.

SCC Commercial and Metal Roofing installed 40 feet of sidewall and 40 feet of counter flashing in Vanceburg, Kentucky. The team ground the area where the valley connects to the EPDM roof and sealed the valley seams with 360s for added durability.

SCC Commercial and Metal Roofing cleaned a roof with a 4200 psi pressure washer using RUST OFF® in Vanceburg, Kentucky. They applied Tack Coat primer, reinforced seams with Spunflex® in RAPID ROOF III coating, and finished with a RED RAPID ROOF® III top coat at two gallons per square.

SCC Commercial and Metal Roofing cleaned and coated a roof in Flemingsburg, Kentucky. The team pressure washed the surface, primed it, sealed seams with reinforcement, and applied a white top coat. The finished roof has an 85% reflectivity rate and a UL-790 Class A fire rating.

SCC Commercial and Metal Roofing removed old shingles and EPDM from a 24'x9' roof section in Vanceburg, Kentucky. They replaced damaged sheathing, installed a Flexion XL PVC membrane, and sealed seams with heat welding. The team properly flashed the chimney, secured the perimeter, and completed shingle replacement and a small sheeting patch.

SCC Commercial and Metal Roofing installed 1x4 boards on two-foot centers across the roof deck in Vanceburg, Kentucky. The crew applied synthetic felt, added vented ridge trim, and fitted new 28-gauge Everlast metal panels. They completed all corners, valleys, drip edges, and metal pipe boots, sealing valleys with Emseal for added protection.

SCC Commercial and Metal Roofing sealed a pipe boot and secured misaligned screws on a ridge cap in Flemingsburg, Kentucky. This repair corrected fastening issues to help maintain roof integrity and prevent future water intrusion.

SCC Commercial and Metal Roofing identified and sealed a roof leak at a fire department in Flemingsburg, Kentucky. Technicians located missing screws on a standing seam roof and applied 360s urethane sealer to prevent further water intrusion.

SCC Commercial and Metal Roofing inspected storm damage to a metal roof in Vanceburg, Kentucky. They documented dents from debris, missing screws, bent transition trim, and a damaged uni-vent. Ridge screws were loose, valleys were pulled up, and an overlapping seam was lifted on one panel. The uni-vent requires full replacement due to limb penetration.

SCC Commercial and Metal Roofing removed gutters and rooftop equipment in Alexandria, Kentucky. They installed EPS insulation and 1½" insulation board across the roof deck. A Flexion® XL membrane system was applied using mechanical fastening and heat welding. New shingles and custom drip edges were added to protect against wind uplift and ensure a continuous roofing surface.

SCC Commercial and Metal Roofing inspected a 15–20-year-old standing seam roof on a commercial building in Trotwood, Ohio. The team assessed previous repairs on exposed screws, rooftop units, and seams to evaluate the roof’s current condition and identify further maintenance needs.

SCC Commercial and Metal Roofing inspected a shingle roof in Maysville, Kentucky. The team assessed the overall condition to identify any signs of wear, damage, or needed repairs. Roof inspections help homeowners maintain roof performance and address issues early.

SCC Commercial and Metal Roofing completed a shingle repair on a commercial building in Maysville, KY. The team removed 500 square feet of shingles and plywood, installed new plywood, synthetic felt, and shingles, added ice and water protection on the eaves, and fitted a new pipe boot.

SCC Commercial and Metal Roofing installed 1x4s spaced two feet apart across the roof deck in Aberdeen, Ohio. The team applied synthetic felt and secured PBR metal panels in a Burnished Slate finish. All seams received mastic sealing to improve durability and weather protection.

SCC Commercial and Metal Roofing inspected a commercial roof in Owingsville, Kentucky. The team assessed leak sources and evaluated whether repairs could extend the roof’s life or if full replacement was necessary. The inspection aimed to help the property owner choose a cost-effective maintenance or replacement plan.

SCC Commercial and Metal Roofing completed a roof inspection in Vanceburg, Kentucky. The team identified leaks caused by deteriorated chimney flashing and worn shingles. They sealed the flashing to prevent further water intrusion while the property owner considers repair or replacement options.

SCC Commercial and Metal Roofing removed the existing EPDM roof and insulation in Cincinnati, Ohio. The crew installed a chute system to remove ballast safely from the roof. They added new insulation boards, secured with fasteners, and completed the project with a Flexion XL roofing membrane installation.

SCC Commercial and Metal Roofing installed a section of Flexion XL single-ply roofing to address leaks and sealed multiple areas on an existing coated foam roof. This service took place in Vanceburg, Kentucky.

SCC Commercial and Metal Roofing repaired roof damage caused by a break-in in Vanceburg, Kentucky. The team replaced disrupted ISO insulation, fixed a damaged HVAC unit, and restored a broken one-way vent to ensure the roof system remained structurally sound and weather-resistant.

SCC Commercial and Metal Roofing repaired multiple leak points on a commercial metal roof in Winchester, Kentucky. The team removed old sealant, replaced damaged screws, and resealed penetrations using White or Bronze Kwik Kaulk and 360S to stop water intrusion and restore roof integrity.

SCC Commercial and Metal Roofing repaired a TPO roof section in Cincinnati, Ohio. The crew cleaned a 2'x3' area, applied tack coat primer, reinforced seams with fabric and basecoat, and finished with a white topcoat. They sealed the front seam at the drip edge using 360s urethane for added protection.

SCC Commercial and Metal Roofing completed a full metal roof installation in Vanceburg, Kentucky. The team removed existing shingles, added 1x4s on two-foot centers, applied synthetic felt, and installed 28-gauge Everlast metal roofing. Work included a vented ridge system, proper flashing, pipe boots, and new gutter guards for improved roof durability and water control.

SCC Commercial and Metal Roofing inspected a leaking roof at a community center in Vanceburg, Kentucky. The team will remove damaged foam, apply new closed cell spray foam averaging 2 inches, then coat it with Benchmark® Base Coat and White PUMA XL Top Coat. Cap trim will finish the project along exterior parapets.

SCC Commercial and Metal Roofing installed a full 28-gauge metal roof system in Midway, Kentucky. The project included new vented ridge installation, drip edge, valleys, chimney boot, 2x6 fascia boards, and center-vented soffit. Crews also built a porch extension with cantilevered rafters and added guttering to the porch section.

SCC Commercial and Metal Roofing inspected an EPDM roof in Georgetown, Kentucky. The inspection focused on leak issues around the HVAC unit. The team identified failed EPDM patches as the cause of the water intrusion. This assessment supported timely attention to potential repair needs.

SCC Commercial and Metal Roofing removed two layers of shingles and installed a new 28-gauge metal roof with a vented ridge system in Vanceburg, Kentucky. The team added 1x4 battens, single bubble insulation, custom mini rake gutters on gable ends, and a metal pipe boot for proper sealing and ventilation.

SCC Commercial and Metal Roofing assessed a church steeple in Vanceburg, Kentucky, after wind damage caused shingles to detach. The team evaluated replacing the existing shingles with metal roofing to align with the rest of the building and improve durability.

SCC Commercial and Metal Roofing inspected a metal roof in Lexington, Kentucky, and replaced failing 20-year-old screws. The crew removed the ridge cap, installed safety gear, replaced all screws with new OSB screws, and fitted a new ridge cap with fresh vents. This service extended the roof’s life without needing full replacement.

Technicians in Vanceburg, Kentucky replaced aging metal roof screws with failed gaskets to extend the roof’s service life. The original screws were over 15 years old. This type of repair helps maintain roof performance without requiring full replacement.

SCC Commercial and Metal Roofing repaired storm damage to a commercial facade in Batavia, Ohio. The team removed 110 feet of damaged facade, installed structural lumber backing, applied Reverse Ran PBR 26-gauge metal panels, and finished with fascia and cap trim. They reinstalled lighting and protected the ground with plywood during equipment use.

SCC Commercial and Metal Roofing completed a full roof replacement in Vanceburg, Kentucky. The team removed shingles and non-functioning chimneys, installed 1x4 battens, applied a single bubble insulation layer, and fitted 28-gauge Everlast metal panels. They finished with drip edge, mini rakes, ridge venting, pipe boots, and all required wall flashings.

SCC Commercial and Metal Roofing installed a new metal roof on a cabin under construction in Vanceburg, Kentucky. This marks their second roofing project for this customer, contributing to the final phase of the cabin's build.

SCC Commercial and Metal Roofing completed an emergency roof repair in Paris, Kentucky. The team cleaned EPDM seams with WAC II, then applied fabric and base coat around an HVAC unit, sealed EPDM patches, and treated a seam near the back wall to prevent leaks and maintain roof integrity.

SCC Commercial and Metal Roofing completed a full metal roof installation on a home in Paris, Kentucky. The team replaced deteriorating plywood, added 1x4s at two-foot intervals, applied synthetic felt, installed drip edges, and mounted 28-gauge Everlast metal panels with ridge cap ventilation and metal pipe boots.

SCC Commercial and Metal Roofing completed a roof inspection on a standing seam metal roof in Hillsboro, Ohio. The roof showed no signs of damage. The property owner requested preventative maintenance and a replacement estimate to assist with future budget planning.

SCC Commercial and Metal Roofing completed a roof inspection in Cincinnati, OH. The team identified potential leak points by measuring interior damage and examining problem areas on the exterior roof surface. This inspection helped locate the source of water entry for further repair planning.

SCC Commercial and Metal Roofing installed 1x4 boards on the roof deck at two-foot intervals in Morehead, Kentucky. Crews added synthetic felt, drip edge, copper-colored Everlast metal panels, mini rakes, transition trim with emseal, pipe boots, w-valleys, and a ridge cap with uni-vent to complete the metal roof system.

SCC Commercial and Metal Roofing identified roof leaks and applied urethane sealant to loose screws across the roof. This service helped stop water intrusion and improve roof stability. Project completed in Vanceburg, Kentucky.

SCC Commercial and Metal Roofing installed 1x4s spaced two feet apart, laid synthetic felt over the roof deck, and fitted #1 28-gauge black Everlast metal panels across the surface. The crew also added mini rakes on the gable ends and installed sidewall flashing in Vanceburg, Kentucky.

SCC Commercial and Metal Roofing removed multiple roofing layers and installed new insulation and single-ply membrane on a steel roof deck in Vanceburg, Kentucky. Workers mechanically fastened insulation, thermally fused membrane seams, reinstalled pipes with proper boots, and sealed parapet walls without cap trim to complete a full roof replacement.

SCC Commercial and Metal Roofing installed 1x4 boards two feet on center across the roof deck in Greenfield, Ohio. The crew applied synthetic felt, installed drip edge at the eaves, and placed 28-gauge Everlast metal panels. They added W-Valley flashing with Emseal, ridge caps with Uni-vent, and finished with new pipe boots.

SCC Commercial and Metal Roofing inspected a church roof in Vanceburg, Kentucky. The team identified a leak and found EPDM membrane uplift near the drip edge. They replaced the damaged single-ply roofing with Flexion XL and repaired a downspout to restore proper drainage and prevent further water intrusion.

SCC Commercial and Metal Roofing installed a 28-gauge metal roof in Vanceburg, Kentucky. The team added 1x4s, synthetic felt, drip edge, ridge cap with Uni-vent, and transition trim. They fitted pipe boots for vents and installed rain and snow guards to protect roof edges. The job followed two-foot on-center spacing across the roof deck.

SCC Commercial and Metal Roofing completed a roof repair in Newport, Kentucky. The crew removed old EPDM material, added a slip sheet, and installed Flexion XL white PVC. They also added a PVC drip edge, counter flashing, and a gutter splash guard to improve function and durability.

SCC Commercial and Metal Roofing inspected a ballasted Rock EPDM roof in Columbus, Ohio. The team checked the membrane condition and ballast coverage to identify any signs of wear or water infiltration. This evaluation supports long-term roof performance and helps plan future maintenance.

SCC Commercial and Metal Roofing inspected a church roof in Suwanee, Georgia. The team assessed the existing EPDM roofing system and planned a commercial coating to help extend its service life. This process helps protect the structure and reduce the need for full replacement.

SCC Commercial and Metal Roofing inspected a concrete roof on a new construction project to evaluate suitable coating options. The assessment focused on identifying materials that provide long-term protection. This service took place in Frankfort, Kentucky.

SCC Commercial and Metal Roofing removed damaged shingles and plywood in Morehead, Kentucky. They installed new plywood, 1x4s on 2-foot centers, a vapor barrier, and 28-gauge Everlast metal roofing. The team added trims, including gambrel, drip edge, and mini rakes, then completed the project with a ridge cap and univent for ventilation.

SCC Commercial and Metal Roofing installed a vapor barrier and 3x3 12 drip edge on the roof eaves in Morehead, Kentucky. Crews added 28-gauge Everlast metal panels, mini rakes on the gable ends, and an endwall. These updates improved weather resistance and roof performance.

SCC Commercial and Metal Roofing installed 1x4 boards across the roof deck, placed synthetic felt, added drip edges, and applied 28-gauge Everlast Ivy Green metal roofing. The crew also installed mini rakes and completed all sidewall, end-wall, and check-mark flashing. This roofing project took place in Grayson, Kentucky.

SCC Commercial and Metal Roofing installed 28-gauge Everlast metal roofing on a residential structure in Vanceburg, Kentucky. The crew added 2x3 drip edges, W-valley flashing with Emseal, a ridge cap with Uni-Vent, flashing for the chimney and dormers, and mini rakes on all gable ends. Gable sidewall was cut directly into the log structure.

SCC Commercial and Metal Roofing conducted a free inspection of a restaurant’s commercial roof in Vanceburg, Kentucky. The team assessed the existing tar coating and began evaluating alternative materials to help extend the roof’s lifespan and improve long-term performance.

SCC Commercial and Metal Roofing completed a full roof replacement in Vanceburg, Kentucky. The team removed two layers of shingles and old metal, installed synthetic felt and 1x4 boards on the roof deck, and applied #1 28-gauge Everlast metal roofing. They also added new fascia boards, flashing, and 6-inch gutters with fascia metal.

SCC Commercial and Metal Roofing replaced a porch roof in Morehead, Kentucky. The crew removed old metal, installed 1x4s on two-foot centers, applied single bubble insulation, and laid new 28-gauge Everlast metal. They added drip edge, a ridge cap with Uni-vent, mini rakes, and metal pipe boots. The project includes a three-year workmanship warranty.

SCC Commercial and Metal Roofing completed a roof inspection in Paris, Kentucky. During the visit, the property owner inquired about a new colonnade awning. The contractor provided a referral to a specialist for the awning while confirming the inspection services.

SCC Commercial and Metal Roofing completed a commercial roof inspection in Aberdeen, Ohio. The team assessed an older roof section for potential replacement. Half of the roof was previously updated, and the client requested a quote for replacing the remaining section.

SCC Commercial and Metal Roofing completed a free inspection of a shingle roof in a residential subdivision in Lexington, Kentucky. The team checked for wear, damage, and potential issues to help the homeowner understand the roof's condition and any needed repairs.

SCC Commercial and Metal Roofing inspected a roof in Grayson, Kentucky. The team identified a few areas that may need repair to extend the roof’s lifespan. The overall roof structure appeared stable during the inspection.

SCC Commercial and Metal Roofing cleared roof drains on a previously completed roofing project in Georgetown, Kentucky. The team removed debris to support proper water flow and prevent pooling. This maintenance work helps extend the roof’s lifespan and reduces the risk of water damage.

SCC Commercial and Metal Roofing replaced metal roofing and installed new 28-gauge Everlast metal in Batavia, Ohio. The team added 1x4 sheathing, drip edge, rakes, and a specialized ridge cap. They also applied rain and snow guards to the eaves, ensuring full edge protection for the roof’s low slope and overhang areas.

SCC Commercial and Metal Roofing completed a full metal roof replacement in Alexandria, Kentucky. The crew removed old shingles, installed 1x4s, synthetic underlayment, and 28-gauge Everlast metal panels. They added flashing, a vented ridge system, and new cedar siding around wall junctions. A custom chimney cap and heated stove pipe boot were also installed.

SCC Commercial and Metal Roofing inspected a commercial building in Maysville, Kentucky. The concrete roof deck showed leaks near the gutter and seam splits. The team plans to submit a proposal for full roof and gutter replacement to restore proper waterproofing and drainage.

SCC Commercial and Metal Roofing installed a single-ply rubber roof over existing EPDM on a flat deck porch in Vanceburg, Kentucky. Crews thermally welded seams, added safety walkway pads, mounted a black hand railing, and finished with red flashing to match the home's exterior.

SCC Commercial and Metal Roofing completed a metal roof installation in Hillsboro, Ohio. The crew installed 1x4s two feet on center, laid synthetic felt, and applied #1 28-gauge Everlast metal panels. They added vented ridge caps, drip edge, mini rakes, and installed sidewall flashing beneath existing siding.

SCC Commercial and Metal Roofing replaced shingle roofing with 26-gauge PBR panel on a commercial building in Vanceburg, Kentucky. The upgrade improves durability and provides a long-term solution for weather protection. This service involved removing the old roofing and installing metal panels suited for commercial use.

SCC Commercial and Metal Roofing added trusses to a brick building, installed bubble insulation, and completed the project with a red metal roof in Vanceburg, Kentucky. The team supported a contractor by enhancing the building’s structure and thermal protection through coordinated roofing work.

SCC Commercial and Metal Roofing inspected wind-damaged 5V metal panels on both sides of a barn in Vanceburg, Kentucky. The inspector documented the damage and prepared a report for the property owner's insurance provider.

SCC Commercial and Metal Roofing inspected a roof with wind-damaged, missing shingles in Hillsboro, Ohio. The team provided a repair estimate for the homeowner's insurance claim. The project concluded with a full roof replacement, restoring the home’s weather protection.

SCC Commercial and Metal Roofing replaced damaged plywood, installed 1x4 supports, and added bubble insulation on a church roof in Grayson, Kentucky. The team installed red 28-gauge Everlast metal roofing, vented ridge caps, pipe boots, flashing around the steeple, drip edge, and mini rakes on the gable ends.

SCC Commercial and Metal Roofing inspected a tobacco barn roof in Augusta, KY. The team identified wind damage on multiple sections along both sides of the roof. The inspection helped assess structural impact and determine necessary roof repairs to prevent further weather-related issues.

SCC Commercial and Metal Roofing installed a new metal roof in Batavia, Ohio. The crew added 1x4 battens, synthetic felt, and a vented ridge cap. They applied #1 28-gauge Everlast metal and completed the job with drip edges, mini rakes, sidewall panels, end wall flashing, and chimney counter flashing. A three-year craftsmanship warranty applies.

SCC Commercial and Metal Roofing performed a roof inspection on a commercial building in Winchester, Kentucky. The team identified multiple leak points and provided repair estimates. The service focused on locating damage and outlining next steps to restore water resistance across affected areas.

SCC Commercial and Metal Roofing completed a roof inspection on a cabin with a shingle roof in Batavia, Ohio. The team scheduled a full roof replacement following the assessment. More updates will follow after project completion.

SCC Commercial and Metal Roofing completed a roof inspection of a blue standing seam metal roof in West Union, Ohio. The team checked panel alignment, seam integrity, and overall condition to help identify any maintenance needs or early signs of damage.

SCC Commercial and Metal Roofing completed a seam repair on a metal roof in Georgetown, Kentucky. The team cleaned the affected area, applied primer to the seams, and installed fabric with a base coat to stop active leaks. This quick fix addressed early signs of water intrusion and helped maintain roof performance.

SCC Commercial and Metal Roofing replaced a shingle roof with 28-gauge Everlast metal in Vanceburg, Kentucky. The team installed 1x4 boards, synthetic felt, a vented ridge system, metal pipe boots, and all standard trim, including rakes, ridge caps, and sidewalls, to complete the metal roof system.

SCC Commercial and Metal Roofing installed 1x4 boards spaced two feet apart, laid synthetic felt, and added drip edge along the eaves in Danville, Kentucky. They installed #1 28-gauge Everlast metal roofing, ridge cap with Uni-vent, pipe boots, and snow and rain guards. The project includes a 3-year craftsmanship and 40-year factory warranty.

SCC Commercial and Metal Roofing installed 1x4s every two feet across the roof deck, laid synthetic felt, and added drip edge along eaves in Hillsboro, Ohio. Crews secured 28-gauge Everlast metal panels, set W-valley flashing with emseal, mounted ridge caps with Uni-vent, and fitted pipe boots to complete the metal roofing system.

SCC Commercial and Metal Roofing repaired a roof in Catlettsburg, Kentucky. The crew removed old metal and plywood from a lean-to section, installed new plywood and a drip edge, applied a single bubble insulation layer, and finished with a new endwall seal and pipe boot installation.

SCC Commercial and Metal Roofing installed 1x4s two feet apart across the entire roof deck in Stanton, Kentucky. The crew applied synthetic felt, drip edge, 28-gauge Everlast metal panels, and all necessary rakes, ridge caps, and trim. They also installed emseal on endwall and transition trim to ensure proper sealing.

SCC Commercial and Metal Roofing removed existing metal from a lean-to garage and installed 12-foot skylights across the roof in Olive Hill, Kentucky. They sealed all seams with mastic, added galvalume transition trim, and installed white drip edges and mini rakes to complete the metal roofing updates.

SCC Commercial and Metal Roofing installed Everloc 26-gauge metal panels on the roof and siding in Richmond, Kentucky. The team fitted a 16-panel standing seam roof with one rib, added drip edges, rakes, and ridge, and completed siding with proper j-channel, rat-guard, and corner trims around windows and doors.

SCC Commercial and Metal Roofing installed a black 28-gauge Everlast metal roof on a garage in Vanceburg, Kentucky. The project matched the existing house roof and included a craftsmanship warranty. The team provided consistent roofing work for a returning homeowner, ensuring uniform coverage across both structures.

SCC Commercial and Metal Roofing performed roof maintenance in Vanceburg, Kentucky. The team sealed pipe boots, vents, and curbs with Kwik Caulk, caulked the sidewall where the parapet wall meets shingles, and repaired three ridge cap shingles to extend the roof’s lifespan prior to replacement.

SCC Commercial and Metal Roofing repaired multiple leak points on a flat roof in Vanceburg, Kentucky. The team identified interior leak locations during rainfall, then returned to seal the affected areas. This approach allowed efficient detection and resolution of water intrusion problems.

SCC Commercial and Metal Roofing completed a single-ply roof inspection in Lexington, KY. The team assessed the roof’s condition to identify potential issues and ensure its continued performance. This service helps property owners understand roof integrity and plan for repairs or maintenance.

SCC Commercial and Metal Roofing restored a metal roof section in Morehead, Kentucky. The team cleaned around the HVAC unit, removed incompatible debris, applied rust-inhibiting primer, sealed seams with caulk, installed basecoat with fabric on horizontal seams, and finished with a white top coat at two gallons per square.

SCC Commercial and Metal Roofing repaired an EPDM roof seam in Vanceburg, Kentucky. The seam had separated, causing a leak. Technicians cleaned the affected area and sealed it using Kwik Kaulk. The team completed the roof repair the same day as the inspection.

SCC Commercial and Metal Roofing repaired a pipe boot leak on a rental home roof in Paris, Kentucky. The team inspected the roof, determined it was still functional, completed the repair, and cleaned the gutters during the visit.

SCC Commercial and Metal Roofing installed 1x4s across the roof deck at two-foot intervals in Owingsville, Kentucky. The team applied synthetic felt, added drip edge to the eaves, installed 28-gauge Everlast metal panels, W-valley flashing with emseal, ridge caps with Uni-vent, and new pipe boots for full metal roof replacement.

SCC Commercial and Metal Roofing replaced a leaking rubber drain beneath existing EPDM roofing in Morehead, Kentucky. The team matched the drain size, cleaned the installation area, fitted the new drain, and sealed the edges to prevent future leaks.

SCC Commercial and Metal Roofing repaired a leak on a commercial building in Morehead, Kentucky. The team identified loose screws causing water entry at a corner seam. They applied Kwik Kaulk to seal the seam and prevent further leakage. This solution helped secure the building’s roof against future moisture issues.

SCC Commercial and Metal Roofing replaced sidewall and endwall flashing on dormers in Olive Hill, Kentucky. The team carefully trimmed the existing siding, installed new flashing, and reattached the j-channel, maintaining the structure's integrity while preserving original materials.

SCC Commercial and Metal Roofing installed a 26-gauge Everlast Everloc standing seam metal roof with 16-inch panels and 1